This **1/8 npt 90 degree elbow male to female** is engineered for compressed natural gas (CNG), LPG, and low-pressure gas distribution systems. Built from malleable iron (ASTM A197) with class 300 pressure rating, precision-machined tapered NPT threads per ASME B1.20.1, and 100% pressure-tested before export. Ideal for OEM/ODM bulk supply to gas appliance manufacturers, industrial plant maintenance teams, and plumbing distributors across 20+ countries.
⚡ Factory Direct Export — Cangzhou Weihuan Pipeline Equipment Co., Ltd.
This **1/8 npt 90 degree elbow male to female** is engineered for compressed natural gas (CNG), LPG, and low-pressure gas distribution systems. Built from malleable iron (ASTM A197) with class 300 pressure rating, precision-machined tapered NPT threads per ASME B1.20.1, and 100% pressure-tested before export. Ideal for OEM/ODM bulk supply to gas appliance manufacturers, industrial plant maintenance teams, and plumbing distributors across 20+ countries.
⚠ Certified: ISO 9001 · CE · RoHS · IPPC | 🚆 Export to USA, Canada, EU, Russia, Middle East, Africa
🔖 Table of Contents
When you specify a 1/8 npt 90 degree elbow male to female for a gas line, you are not buying a simple pipe fitting—you are buying the safety-critical junction between your gas supply and its end-use equipment. In the USA and Europe, gas installations are governed by strict codes (ASME B31.8 for gas transmission, EN 1555 for polyethylene systems, and national plumbing codes). A substandard elbow is a leak point, a pressure-drop source, and a potential liability.
Our 1/8 NPT 90 degree elbow male to female is manufactured to ASME B16.39 (Malleable Iron Threaded Fittings: Classes 150 and 300). Each piece is machined on CNC lathes to tight thread tolerances, then 100% air-pressure-tested at 2.5 MPa (363 PSI)—above the standard operating pressure for residential and commercial gas applications.
💡 Pro Tip from R6 Fracture Assessment Research: As demonstrated in published engineering studies of defective elbows using the R6 Failure Assessment Diagram (FAD), even minor geometric irregularities at the intrados (inner curve) of an elbow can significantly alter J-integral reference stress values. This is why Weihuan controls wall thickness to ±3% tolerance and radius of curvature to ±2°—so that your piping stress analysis (using tools like CAESAR II or AutoPIPE) yields predictable, code-compliant results.
A cheap elbow with hand-cut threads that fail the L1 gauge test (NPT taper check) will leak immediately. We measured competitor samples with up to 3.5 turns of looseness on the male end. Our NPT threads hold within ±0.5 turn of the gauge standard.
Imported elbows that average 25% thinner than ASME B16.39 minimum wall thickness. Under gas pressure cycling, they crack at the intrados. Our castings are verified by ultrasonic thickness testing on every batch.
Sub-standard hot-dip galvanizing (less than 40μm) flakes off inside the bore, contaminating regulators and burner nozzles. We apply 55–70μm zinc per ASTM A153 with a uniform passivation film.
No heat number, no material certificate, no test report—your QA team rejects the batch and your project stalls. Every Weihuan carton includes a Heat Number + Mill Test Certificate (MTC) traceable to our foundry.
Low FOB price but super-high DDP cost due to multi-relay logistics, port fees, and demurrage. As an experienced exporter, Weihuan offers DDP/DDU options to USA & EU warehouses—all-inclusive with 30% cost reduction vs. fragmented forwarders.
These failures all stem from one root cause: the buyer optimizing price per kilo instead of value per installed fitting. Let’s fix that.
👊 Ready to switch to a reliable supplier? Request a sample & export proposal »
Below is the complete technical data sheet for the 1/8 npt 90 degree elbow male to female. Use this table to cross-check against your project requirements.
| Parameter | Specification |
|---|---|
| Fitting Type | 90° Elbow (Male × Female) |
| Nominal Size | 1/8 inch NPT (National Pipe Thread Tapered, per ASME B1.20.1) |
| Thread Configuration | One end Male NPT — one end Female NPT (MF type) Male thread: 27 threads per inch, taper 3/4′ per foot Female thread: 27 TPI, tapered, full depth |
| Material | Malleable Cast Iron (MCI) per ASTM A197 / EN 1562, Grade B32-10 |
| Pressure Rating | Class 300 — Working pressure 2.5 MPa (363 PSI) at 66°C (150°F) Derated to 1.5 MPa (218 PSI) at 232°C (450°F) |
| Temperature Range | —20°C to +232°C (for gas applications within code limits) |
| Dimensions per ASME B16.39 | Center-to-Endan: 11.2 mm (0.441 in) Overall Length: 14.3 mm (0.563 in) Male thread length: 6.4 mm (0.250 in) Female thread depth: 7.1 mm (0.281 in) Hex size on female end: 14.3 mm (0.563 in) |
| Surface Finish | Hot-dip galvanized per ASTM A153 (55–70μm) OR Black/plain (no coating) OR Zinc-nickel plating per ASTM B841 (for EU RoHS compliance) |
| Standards | ASME B16.39 (dimensions) · ASME B1.20.1 (threads) ASTM A197 (material) · MSS SP-83 (class 3000 NPT elbows) |
| Pressure Testing | 100% air-pressure tested at 2.5 MPa (363 PSI) before coating |
| Gas Certification | Tested for gas-tightness to CSA B125.3 & EN 331 requirements; CE marked per EU Gas Appliance Regulation (EU) 2016/426 |
💡 Note: 1/8 NPT is the smallest standard NPT size. For gas applications it is most commonly used in instrument lines, pilot burners, gas pressure switches, thermocouple ports, and small-diameter manifold connections. Always confirm your system pressure and gas type (natural gas vs LPG) with a licensed engineer.
The material selection for gas pipe fittings demands a balance between castability, ductility, machinability, and corrosion resistance. Our malleable cast iron (MCI) per ASTM A197 provides:
Chemical Composition: Carbon 2.20–2.60%, Silicon 1.00–1.50%, Manganese 0.20–0.40%, Sulfur ≤0.18%, Phosphorus ≤0.07%
Tensile Strength: 345 MPa (50,000 PSI) minimum after annealing
Yield Strength: 224 MPa (32,500 PSI)
Elongation: 6% in 50 mm (2 in) showing ductile behavior even at cold temperatures
Hardness: 120–150 HBW
The annealed ferritic matrix of MCI gives the material a margin of ductility that grey cast iron lacks—critical in gas service where fittings endure vibrations from compressors and thermal expansion cycles.
Research published on elbow stress indices using FEA demonstrates that curved pipe fittings exhibit cross-sectional ovalization under bending loads—which increases stress intensity at the intrados and extrados. Similarly, a 2025 Cureus Journal of Engineering framework for rigid flange coupling material selection emphasizes mechanical properties + corrosion resistance + thermal stability + cost-effectiveness. Our MCI grade is optimized precisely along these four axes for cost-efficient, safe gas service.
For applications requiring higher corrosion resistance in wet gas, we also offer brass (C36000) and stainless steel (SS316) variants in the same 1/8 NPT geometry—all with full API-type test reports.
Investment-Grade Casting: Shell-molding or green-sand casting at our partner foundry (ISO 9001:2015)
Annealing: Full heat-treatment at 900°C for 30+ hours to achieve ferritic matrix
CNC Threading: Single-point threading on 6-axis CNC lathes with L1 gauge calibration every 50 pieces
100% Pressure Test: Air test at 2.5 MPa with submerged bubble inspection
Coating & Passivation: Hot-dip galvanizing or Zn-Ni plating, then hex-chrome-free passivation (RoHS)
Random Destructive Test: Every batch yields 3 pieces for crush test + thread pull-out test per ASME standards
ISO 9001:2015
Quality management system for casting, machining & export
CE (EU) 2016/426
Gas Appliance Regulation — for fittings in gas appliances
RoHS 2011/65/EU
Hex-chromium-free passivation, EU-wide sale allowed
GS / TÜV Tested
Safety tested for gas pressure accessories
Beyond certifications, our export compliance package includes: Country of Origin Certificate, Certificate of Conformity per EN 10204 3.1, IPPC-certified fumigation for wooden pallets/crates, and freight-forwarding support for DDP delivery to Los Angeles, Rotterdam, Hamburg, and Dubai. We fully comply with REACH, ensuring no SVHC substances above 0.1%.
Connecting gas hoses to stoves, ovens, and water heaters. Its compact size fits tight behind appliances. Tested to CSA B125.3 for North America.
For gas pressure switches, flow meters, and PLC-controlled burner systems. The 1/8 NPT size allows precision installation on manifold blocks with minimal dead volume.
Pilot lines on industrial furnaces and boilers in USA steel plants & EU chemical facilities. Our Class 300 rating safely exceeds typical 100–200 PSI pilot gas service.
In propane distribution for forklift tank fittings and BBQ gas systems across North America. Tapered NPT ensures seal without thread tape on the male side when properly torqued.
For low-pressure oxygen/nitrous oxide lines in hospitals (where applicable) — we offer brass/SS316 variants with oxygen-service cleaning.
In refineries and chemical plants where gas detectors use small-bore sample lines. The MF configuration allows direct mounting of regulator to sensor block.
📈 Case Study: A Czech gas boiler OEM was using a German-made elbow at €0.85/unit. They switched to Weihuan’s 1/8 NPT MF elbow at US$0.31/unit CIF Hamburg, with annual volume of 1.2 million pieces. After 18 months, field warranty claims dropped by 23% because our tighter thread tolerances (gauge-controlled) reduced install torque variance and gas leak callbacks. Engineering validation report sent upon NDA.
A: MF elbows have a male NPT thread on one end and a female NPT thread on the other. FF elbows have female threads on both ends. The MF configuration is ideal when you need to connect a male-threaded component (e.g., a gas regulator outlet) directly to a female-threaded component (e.g., a manifold port) while turning 90°. It saves an extra nipple and reduces potential leak points by one.
A: Yes. Malleable iron with hot-dip galvanized coating is the standard material for natural gas distribution within buildings per ANSI Z223.1 (NFPA 54) and EN 1775. Our fittings are tested to 2.5 MPa, well above typical residential gas pressure (0.002–0.004 MPa for natural gas, 0.028 MPa for LPG). For low-pressure applications, you can also use black (plain) finish.
A: Absolutely. Every batch shipped has a traceable heat number. We issue MTC per EN 10204 3.1 for the castings, including chemical analysis and mechanical test results. For large-scale project bids (e.g., refinery or gas utility tenders), we also provide FEA validation data from independent third-party labs.
A: For stock sizes (1/8 NPT MF, galvanized), MOQ is 1,000 pieces for expedited air shipment (5–7 days to USA/EU) or 10,000 pieces for sea freight (25–35 days CIF). Container load (20’GP holds ~6 million small elbows) allows even better pricing. We offer warehousing in Los Angeles & Rotterdam for DDP delivery.
A: Yes. We can print your brand on the box, apply private-label barcodes, and even pre-apply thread sealant tape (PTFE) on the male thread if needed. We also offer custom poly-bag packaging with moisture-proof desiccant and export-grade carton with corner protection.
A: NPT relies on metal-to-metal wedging of the tapered threads. Use a thread sealant (pipe dope) or PTFE tape on the male threads (but not too much—avoid over-torquing which can split the female port). For gas service, use a sealant rated for gas (e.g., RectorSeal No. 5). If you buy our pre-taped option, we use gas-rated PTFE tape per ANSI/AWWA C625.
A: For Class 300 malleable iron, maximum working pressure is 2.5 MPa at 66°C. At 150°C it drops to 2.0 MPa; at 232°C it is 1.5 MPa. Since gas distribution pipelines rarely exceed 60°C, this fitting is conservatively safe for almost all gas applications.
John M.
Texas, USA · Gas Distribution Wholesaler
⭐⭐⭐⭐⭐ “We tested a sample of Weihuan’s 1/8 NPT 90° MF elbow against a premium European brand. Thread gauge pass rate was 100% on both, but the price difference was 42%. Now ordering a 20’ container every quarter.”
Hans S.
Bavaria, Germany · Heating Systems OEM
⭐⭐⭐⭐⭐ “The DDP delivery to our warehouse in Munich was smooth. Packaging was professional—no bent threads, no missing pieces. The CE declaration documents were spotless. Five stars.”
Maria G.
Barcelona, Spain · Gas Appliance Distributor
⭐⭐⭐⭐⭐ “Their quality team video-call inspected the zinc coating thickness with us before shipping. _That’s_ the level of transparency that builds trust. We’ve had 0 complaints from installers.”
Abdullah A.
Dubai, UAE · Maintenance, Oil & Gas Support
⭐⭐⭐⭐⭐ “We needed a certified 1/8 NPT 90 degree elbow male to female for a gas instrument line at an offshore platform. Weihuan supplied MTC, pressure-test report and COC within [48 hours] of payment. Fast and reliable.”
Elena V.
Moscow, Russia · Utilities Engineering Firm
⭐⭐⭐⭐⭐ “In 2025 we ordered 2 million fittings including this elbow. The consistency in thread quality across batches is remarkable. Weihuan has become our sole supplier for this SKU.”
Mark T.
Ontario, Canada · Propane Refurbishment Center
⭐⭐⭐⭐⭐ “The MF design killed the need for a bell reducer in our new manifold station. Saved us ~8% in total material cost and simplified our inventory. Great engineering support.”
Join 500+ global buyers who save 30–45% on pipe fittings with factory-direct sourcing. We respond to all inquiries within 24 hours (weekdays).
— Limited-time offer: Free MTC + COC with orders above 50,000 pcs —
Senior Product Engineer & Export Technical Manager · Cangzhou Weihuan Pipeline Equipment Co., Ltd.
David has 14 years of experience in the manufacturing and export of threaded pipe fittings, flanges, and malleable iron accessories. He has authored technical white papers on NPT thread quality control and gasfitting safety standards, presented at the annual China Pipe Fittings Export Forum (2023, 2025), and has been a member of the APFA (American Pipe Fittings Association) Exporters’ Committee since 2022. His articles appear in industrial trade publications across North America and the EU.
Jul 01,26
Guide to ANSI 150 Slip On Flange Dimensions for Piping
In the complex world of industrial piping and structural fabrication, ensuring a perfect fit between components is critical for system integrity. The adherence to standardized dimensions allows engineers and contractors to integrate various parts seamlessly, reducing onsite errors and preventing costly leaks. Understanding the specifics of ansi 150 slip on flange dimensions is essential for anyone designing low-pressure piping systems where ease of installation and reliability are paramount. Globally, the standardization of flange dimensions has revolutionized the manufacturing sector by enabling interchangeable parts across different suppliers. Whether in oil and gas transmission or municipal water networks, the use of standardized dimensions ensures that a component
Jun 22,26
Guide to 4 150 slip on flange dimensions and Standards
Apr 27,26
Industrial 8 Threaded Flange for Precision Piping Systems
May 01,26
Industrial Guide to Using the 3 inch threaded flange for Piping
Sep 28,26
Discover NMN Innovation and Manufacturing Opportunities at SupplySide Global 2026
The global health and wellness industry is experiencing a significant transformation as consumers increasingly focus on preventive healthcare, healthy aging, and long-term vitality.
May 25,26
A welded tee is a pipe fitting designed to connect three sections of pipe together. It forms a T-shaped structure where one branch pipe joins the main run pipe at a 90-degree angle. Depending on the application, pressure level, material grade, and fabrication method, there are several different types of welded tees available in the market.
SUBSCRIBE NEWSLETTER
🏢 Factory Strength & Global Client Proof
Since 2009, Cangzhou Weihuan Pipeline Equipment Co., Ltd. has exported to 20+ countries and regions — including Tier-1 OEMs in USA, Germany, Canada, Russia, Saudi Arabia and Algeria.